Home / Blog / Article

Infrared Heaters for the Lanai: How They Work, Where They Go and Who Controls Them

A winter evening on a Naples lanai is pleasant until a front comes through. The breeze picks up, the temperature drops after sunset, and by eight o'clock everyone has moved indoors. Infrared heaters keep the lanai usable on those nights. Installed properly they sit in the ceiling or on the wall, out of the way, and run from the same keypad as the lights.

This is how CITE plans outdoor heating for a lanai: Eurofase heaters, wiring by CITE Electric and control by CITE Solutions.

How infrared heat differs from a gas patio heater

A gas patio heater warms the air around it, and on a screened lanai with a breeze moving through, that air leaves almost as fast as it is heated. An infrared heater works differently. It sends radiant heat to whatever it faces, people, furniture and the floor, the way the sun warms your face on a cool day while the air stays cool. Step out of its path and you feel the difference at once.

On a lanai that changes several things. There is no propane tank to refill or hide, no open flame under a screen enclosure or a timber ceiling, and no long wait for the heater to come up to temperature. The heat lands where the heater is aimed, so placement matters more than raw output, and the heater is fixed to the structure instead of standing in the middle of the seating like a typical patio heater in Naples.

The 2026 Eurofase range

Eurofase makes four heater lines, and between them they cover most lanais we see.

  • EF Series. From 1,500 to 6,000 watts, with a single or dual element, in black, white, stainless or any RAL color, finished with laser cut decor plates. This is the heater for larger lanais and outdoor kitchens.
  • EF Series Marine Grade. The EF built in 316 stainless steel, for homes within a few miles of the shore. Flush mount kits for recessed ceilings come in 39 and 61 inch sizes.
  • LP Series. A low profile heater, 4.75 inches tall and 62.75 inches long, at 3,000 or 4,000 watts, in black or stainless. It suits a ceiling where a deeper heater would sit in the sight line to the water.
  • Vellura. Freestanding, tabletop or pendant, at 1,500 watts on 120 volts, with a dimmable 3000K LED light and nine shade colors. It heats and lights a seating group or a dining table from one fixture, which makes it the natural choice where lanai lighting and heating should come from the same piece.

Placement and mounting

Heaters are placed against the seating, not spread evenly across the ceiling. We look at where people sit and eat, the ceiling height, the direction the breeze usually comes from and where the screens are, then aim each heater at one group of seats or one table.

There are five ways to mount them:

  • Flat on a wall or ceiling
  • Angled on a wall or ceiling, to throw heat toward the seating from the edge of the space
  • Recessed flush into the ceiling, so only the face shows
  • On a suspension kit from a vaulted ceiling, bringing the heater down to a useful height
  • On an 8 foot pole, where there is no wall or ceiling in the right place

Recessed flush mounting gives the cleanest finish and is easiest to plan while a ceiling is being built or reworked. On a finished lanai, surface or angled mounting is usually the better answer.

Salt air and the Marine Grade

Salt is why exterior equipment fails early in Naples, on Marco Island and along the Gulf side of Bonita Springs. It gets into fixtures, fasteners and terminals, and ordinary finishes pit and stain. The EF Series Marine Grade is made in 316 stainless steel for homes within a few miles of the shore, and that is where we put it. Further inland, the standard EF and LP finishes are the usual choice.

Eurofase also stands behind the product: if a heater fails to perform, Eurofase repairs or replaces it for up to three years from purchase.

Wired in zones by CITE Electric

Wall and ceiling heaters are electrical loads to be wired, not appliances to plug in. CITE Electric wires them in zones through a relay panel: the seating area, the dining table and the outdoor kitchen each on its own zone, so you heat only the part of the lanai you are using. Each zone's circuit is sized to the heaters on it, the work is permitted and inspected, and if the panel has no room for new circuits, the load calculation shows it before anything is ordered.

With one owner and one team behind both companies, the circuit layout and the control layout are drawn together. The relay panel goes where the control system can reach it, and nobody has to referee between an electrician and an integrator who have never met.

On the keypad, set up by CITE Solutions

CITE Solutions puts each heater zone on the Lutron or Crestron keypad, so the heat sits next to the lights and the shades. One button brings the seating zone on. A dinner scene can raise the table lighting, lower the lanai shades and start the dining zone heater together. A zone can also run on a timer, or both: switched on by hand and off on a timer, so a heater is never left running all night.

For a smaller lanai with one or two heaters and no control system, the Eurofase app runs them, with a four hour auto shut-off.

Send a photo, get a heater layout

Eurofase offers heater layouts, and we use them. Reply to our heater email, or email a photo of the space to office@cite-solutions.com, and we come back with a heater layout and a time to visit. The visit is where we check the ceiling, the panel and the route for the wiring. A useful photo is taken from the house looking out, and it helps to tell us the rough size of the lanai, the ceiling height, whether it is screened and how far the house is from the water.

Lanai heater questions

Do infrared heaters work on a screened lanai?

Yes, infrared heaters suit a screened lanai because they warm people and surfaces directly instead of heating air that the breeze carries away. They mount on the wall or ceiling, so the floor stays clear.

Which Eurofase heater is best close to the beach?

The EF Series Marine Grade, made in 316 stainless steel, is the Eurofase heater for homes within a few miles of the shore. Flush mount kits in 39 and 61 inch sizes set it into a recessed ceiling.

Can lanai heaters run from a Lutron or Crestron keypad?

Yes, once the heaters are wired in zones through a relay panel, each zone can go on a Lutron or Crestron keypad, on a timer, or on both. CITE Electric does the wiring and CITE Solutions programs the keypad.

Do I need an electrician to install an infrared lanai heater?

Yes, wall and ceiling heaters are wired on their own circuits by a licensed electrical contractor and the work is permitted. On a CITE project that is CITE Electric, under its unlimited Florida license.

What warranty comes with Eurofase heaters?

Eurofase repairs or replaces a heater that fails to perform for up to three years from purchase. Keep the purchase details with the house records.

Want the lanai warm for the next cold front? See our outdoor living work, or get in touch through the contact page and tell us about the space.

Talk to the people who will do the work.

The property, the rooms and the systems you want. We reply within two business days.